﻿================================================================
Fineline UI
================================================================
----------------------------------------------------------------

Version:                 	4.2407.18.0     
> CutCharts C.7
----------------------------------------------------------------
Version:                 	4.2310.26.0
> Q4 2023 release
> Corrected issue so that FLGC errors are sent to FineLine HMI properly.

Version:                 	4.2303.22.0
> Q1 2023 release
> Improved processing time for embedded Burny UI.
> Added Disable Dispense ACM for Burny system.
> Updated Cutlinc trademark branding.
> Updated torch part numbers displayed on screen. 
----------------------------------------------------------------

Version:                 	4.2303.06.4     
> Update to resolve issue with Fineline-Burny UI only.  Improves p
  processing time for ACMs.  
----------------------------------------------------------------

Version:                 	4.2211.17.0     
> CutCharts C.6
----------------------------------------------------------------

Version:                 	4.2210.14.0     
> Updated to resolve issues with languages. 
----------------------------------------------------------------

Version:                 	4.2209.23.0     
> CurCharts C.5
      Note: C.2-5 was skipped for Service Pack release.
> Updates the setup page, Process box to improve clarity.
> Improve Language Updates.
   Added Language Support for:
          "Hungarian","Magyar"
          "Czech","čeština"
          "Slovak","slovenský"
> Added Support for APC and VMD intercommunication for 
  embedded job parameters.
> Resolved issue, synchronizing Start IO, using CutLinc.

----------------------------------------------------------------

Version:                 	4.2206.6.0     
> CurCharts C.1
      Note: C.0 was skipped for Installer release.
> Update H20 Purge, clearing H20 from lines
> Added APC errors, error actions,  and error handlers.
> Resolved unreported issues.

----------------------------------------------------------------

Version:                 	4.2204.8.0     
> CurCharts B.8  
      Note: B.5 was skipped for Installer release.
	  
----------------------------------------------------------------

Version:                 	4.2204.4.0     
> CurCharts B.6  
      Note: B.5 was skipped for Installer release.

----------------------------------------------------------------

Version:                 	4.2203.11.2     
> CurCharts B.4

----------------------------------------------------------------  
----------------------------------------------------------------

Version:                 	4.2112.17.2     
> CurCharts B.3
> Added communication support for torch telemetry.
> Resolved ACM Invalid Process, added INVALID_PROCESS event.

----------------------------------------------------------------

Version:                 	4.2109.15.2     

> CutCharts B.2
> Support for Air_H20 and N2_H20 gas selections were added to Host adapters. 
> The Lock Feature has been removed.
> The selection dialogs have changed. SCItems and CScItems have been removed.  The “Tiled” buttons have been removed for a scrollable list.
> The Material and Thickness have changed locations to improve the workflow.
> The “Selected Chart Filter” Feature on the Settings page has been removed.  The quality of cut can be filtered when selecting the Thickness.  This is the second column in the Thickness list dialog.  Click the second column header and the filter will change.  The TorchEnable selection box on the setup page has a new selectable 
	1.	Multiple torch configurations will be synchronized by default. The operator will have the ability to disable a torch but they will be synchronized if enabled.
	2.	The type of power supply will be displayed under the torch selection button.  This allows for quick identification without navigation to another screen when first becoming failure with the systems configuration. (FL170, FL300, and FL450)
	3.	When more than one torches are enabled the setting will be applied to all torches.
	4.	If more than one torch is selected and all the torch groups don’t have APCs then the APCs will be disabled (unselected).  Below Torch 1 Has APC but torch 2 does not.  The operator cannot enable the APC in the first image.  After Torch 2 is disabled then the APC for Torch 1 can be selected.  If the operator enables Torch 2 while the APC is enabled on torch 1, the APC will be disabled.  The operator will be prompted to make a new Material selection because H20 will no longer be available. 
	5.	If a Fineline 170 and a 300 are both selected for operation the overall cutting current will be limited to 170 amps.
	6.	A Fineline 450 cannot be selected for operation together with a Fineline 300 or 170.   The Fineline 300s and/or 170s can be disabled first then the 450 can be enabled.
> All the selection dialogs have been replaces with selection lists.  Selecting Current will display a Current sorted list to select from.  This is unfiltered.
> Selecting Thickness will display a Thickness sorted list.  The middle column displays the Cut Quality tag and the operator can filter by click that header.  “N” is no filter.

----------------------------------------------------------------

Version:                 	4.2108.13.0  
 
> Consolidated release, no major changes.

----------------------------------------------------------------

Version:                 	3.2107.8.0     

> Added Marking gas saver purge routine. Only purges marking when marking is selected.
> Supports APC features.
> Supports multi-torch control.  Controls 1 to 4 torches. 
> Supports LC300M Cut Chart version B.1
> Purge Order changes based on process selection
> Purge for 5s when H20 is selected and the process is changed.
> Added UI configuration capability for Gas Controller Arc Hold and Inverting CTP, Inverting TAC and selecting AutoCTP.
> Added error for ERR_INVALID_CHART_FORMAT operator selected H2O with APC disabled.
> CLSuite DLLS have been replaced with a single dll.

----------------------------------------------------------------

version: 				3.2011.18.4

> Added Support For Burny Integration 
> Added Support for Burny ACM.

----------------------------------------------------------------

version: 				2.2009.22
> UI Application Name was changed to FineLine
> will auto start CLFServer if its singleton mutex is not active
> will log all event to Public Log temp Folder
> added support for Adapter name to public application configuration nvm.xml file
> modified Error reporting, first error received is displayed on status bar
> modified Channel select disable, disable all one UI button
> modified error log verbose reporting
> added PAL support advertising information about chart manager selections
> Updating, pending review, language translations for 8 languages.
> Updates all support directories to auto create path and files.
